1.清潔機器時，只能擦拭電箱，不能沖洗。
1. When cleaning the machine, only wipe the electric box, not wash it.
2.調整主軸密封圈，拆下泵芯和進給支架，然后擰緊三個螺釘。螺釘擰緊后的標準：8英寸可動手可輕松拉動主軸螺釘。
2. Adjust the main shaft seal ring, remove the pump core and feed bracket, and then tighten the three screws. Standard after screw tightening: 8-inch can easily pull spindle screw by hand.
3.在施工現場移動機器時，不管間隔如何，都有必要拔掉電源線。
3. When moving the machine on the construction site, it is necessary to unplug the power line regardless of the interval.
4.機器作業時，有必要關閉并鎖上電箱門，以避免灰塵和濕氣侵入并損壞機器部件。
4. When the machine is working, it is necessary to close and lock the electric box door to avoid dust and moisture invasion and damage to machine parts.
5.在作業之前和之后，有必要給軸承箱加油，并經常查看變速箱油。
5. Before and after operation, it is necessary to oil the bearing box and check the gearbox oil frequently.
6.每次清潔泵芯時，有必要加少數硅油光滑和防刺繡。目的是維護轉動鐵芯免于生銹，并在下次運用后順暢啟動。
6. When cleaning the pump core, it is necessary to add a small amount of silicone oil for smoothness and anti embroidery. The purpose is to protect the rotating core from rusting and to start smoothly after the next operation.
自上料攪拌車選用全液壓技術，因而要考慮所有液壓技術是否先進，以及液壓視覺質量。因為動力來自發動機，除了考慮發動機的功能和質量外，還有必要考慮底盤的功能，承載能力和質量。在維護車輛設備的過程中，有必要嚴格依照正確的操作過程進行，以堅持作用。
Since the full hydraulic technology is selected for the self feeding mixer, it is necessary to consider whether all the hydraulic technology is advanced or not, and the visual quality of the hydraulic system. Because the power comes from the engine, in addition to considering the function and quality of the engine, it is also necessary to consider the function, bearing capacity and quality of the chassis. In the process of maintenance of vehicle equipment, it is necessary to strictly follow the correct operation process to adhere to the role.
經過自上料攪拌車清潔內部混凝土的辦法
Method of cleaning internal concrete by self loading mixer
在咱們的日子中，自上料攪拌車是一種運送混凝土的特殊車輛。通常在車輛后邊裝置一個大型水箱來攪拌混凝土。可是，因為咱們需要在長期運用期間清潔車內的混凝土，咱們將在下面介紹具體的清潔辦法。
In our days, self loading mixer is a special vehicle for transporting concrete. A large water tank is usually installed behind the vehicle to mix concrete. However, since we need to clean the concrete inside the vehicle during long-term use, we will introduce the specific cleaning methods below.
1.準備應急驅動軟管，關閉混凝土主動攪拌車，然后拆下液壓馬達上的高壓油管接頭。
1. Prepare the emergency drive hose, close the active concrete mixer, and then remove the high-pressure oil pipe joint on the hydraulic motor.
2.拆下高壓油管，并將其與毛病車上相應連接器的應急驅動軟管連接。
2. Remove the high-pressure oil pipe and connect it with the emergency drive hose of the corresponding connector on the defective vehicle.
3.發動機攪拌車，其操控手柄設置在卸料方位，以排除車內混凝土
3. The control handle of the engine mixer is set at the unloading position to remove the concrete in the truck
4.緊急驅動完成后，拆下驅動軟管并恢復車輛的原始狀態。
4. After the emergency drive is completed, remove the drive hose and restore the original state of the vehicle.
Thank you for reading. This article is from Zhongke Jufeng mixer. For more information and questions, please click: http://www.top2010.cn We will continue to work hard to provide services for you, thank you for your support!
上一篇：水泥自動攪拌車有哪些注意事項？
下一篇：自上料攪拌車機油怎么使用是正確的？
