（一）小型攪拌車攪拌筒停轉的處理
（1） Treatment of small mixer drum stop running
檢查攪拌筒托輪以及馬達，看是否是有土石雜物卡住，如果有，將雜物清理干凈即可。如果不是由于雜物卡住無法轉動，立刻呼叫救援車。在有條件排放混凝土的情況下，可以將馬達上的高壓軟管的管接頭卸下，旋轉攪拌筒，讓攪拌筒檢修孔向下，將混凝土從檢修孔排出。救援車到場后，將故障車馬達上的高壓軟管卸下，接上救援用高壓軟管，另一端接在救援車油泵上，同時把應急用的回油管連接在故障車馬達泄油口位置，另一端連接在救援車油泵回油口，利用救援車對故障車的小型小型攪拌車進行控制旋轉，直至混凝土排出。如有條件的情況下，可以直接更換出現故障的馬達，更換馬達后接好各個油管，攪拌筒即可正常旋轉。
Check the supporting wheel and motor of the mixing drum to see if there is any debris stuck. If so, clean up the debris. If it is not due to debris stuck, call the rescue vehicle immediately. Under the condition that concrete can be discharged, the pipe joint of the high-pressure hose on the motor can be removed, and the mixing drum can be rotated to let the access hole of the mixing cylinder go down to discharge the concrete from the manhole. After the rescue vehicle arrives at the scene, remove the high-pressure hose from the motor of the fault vehicle, connect the high-pressure hose for rescue, and connect the other end to the oil pump of the rescue vehicle. At the same time, connect the emergency oil return pipe to the oil drain port of the motor of the failure vehicle, and connect the other end to the oil return port of the oil pump of the rescue vehicle. The small-scale mixer truck of the failure vehicle is controlled to rotate until the concrete is discharged. If conditions permit, the motor that fails can be replaced directly. After the motor is replaced, each oil pipe is connected, and the mixing drum can rotate normally.
（二）小型攪拌車攪拌筒的構造和工作原理
（2） Structure and working principle of mixing drum of small mixer truck
小型攪拌車攪拌筒絕大部分都采用梨型結構，攪拌筒通過支承裝置斜臥在機架上，可以繞其軸線轉動，攪拌筒的后上方只有一個筒口分別通過進出料裝置進行裝料或卸料。整個攪拌筒的殼體是一個變截面而不對稱的雙錐體，外形似梨型，底段錐體較短，端面封閉并焊接著法蘭，通過連接法蘭用螺栓與減速器聯結。
Most of the mixing cylinders of small-sized mixer truck are pear shaped. The mixing drum is inclined on the frame through the supporting device and can rotate around its axis. There is only one opening on the upper rear of the mixing drum, which is loaded or unloaded through the feeding and discharging device respectively. The shell of the mixing drum is a variable cross-section and unsymmetrical double cone, the shape is pear shaped, the bottom cone is short, the end face is closed and welded with flange, and the reducer is connected with bolts through the connecting flange.
上段錐體的過度部分有一條環行滾道，它焊接在垂直于攪拌筒軸線的平面圓周上，整個攪拌筒通過連接法蘭和環形滾道傾斜臥置在固定與機架上的減速器殼體和一對支承滾輪所組成的三點支承結構上，由減速器帶動平穩的繞其軸線轉動。在攪拌筒滾道圓周上部，通常設有鋼帶護繞，以限制攪拌筒在小型攪拌車顛波行駛時向上跳動。
The transition part of the upper cone has a circular raceway, which is welded on the plane circumference perpendicular to the axis of the mixing drum. The whole mixing drum is inclined to lie on the three-point support structure composed of the reducer shell fixed on the frame and a pair of supporting rollers through the connecting flange and the annular raceway, and the reducer drives the smooth rotation around its axis. A steel band is usually set on the upper part of the circumference of the mixing drum raceway to limit the upward jump of the mixing drum when the small mixer truck is running in a bumpy wave.
小型攪拌車攪拌筒的內部結構，它與雙錐形和梨形攪拌機的內部結構都不同，這是為了適應在單一筒口不傾翻反轉卸料和進料攪拌的工藝要求而設計的。攪拌筒從筒口到筒底沿內壁對稱焊接著兩條連續的帶狀螺旋葉片，當攪拌筒轉動時，兩條葉片既被帶動作圍繞攪拌筒軸線的螺旋運動，這是攪拌筒對混凝土進行攪拌或卸料的根本裝置。另外，為了加強攪拌效果，在攪拌筒的中下部兩條螺旋葉片間加裝有輔助攪拌葉片。
The internal structure of small mixer drum is different from that of double cone mixer and pear shaped mixer. It is designed to meet the process requirements of unloading and feeding mixing without overturning at a single drum mouth. Two continuous ribbon spiral blades are symmetrically welded along the inner wall from the barrel mouth to the bottom of the mixing drum. When the mixing drum rotates, the two blades are driven to move around the axis of the mixing drum, which is the fundamental device for mixing or discharging concrete. In addition, in order to enhance the mixing effect, an auxiliary mixing blade is installed between the two spiral blades in the middle and lower part of the mixing cylinder.
With the summary above, we hope to help our customers. If you have any questions that you don't understand or ask for help, please click our website: http://www.top2010.cn Or call consultation, we will try our best to solve it for you
上一篇：自拌水泥自動攪拌車的剎車問題怎么解決？
下一篇：選擇水泥自動攪拌車哪些優勢不能忽略？
