The belt conveyor has the advantages of strong conveying capacity, long conveying distance, simple structure, easy maintenance, and convenient programmed control and automatic operation. Since the loading mixer truck and concrete mixing plant can not lack belt conveyor, the belt conveyor can be used to transport materials. Therefore, during use, attention should also be paid to maintenance.

1、傳動裝置的維護與保養。使用前應加潤滑油，潤滑油牌號為L(zhǎng)KC100，150#中負荷極壓工業齒輪油。

1. Maintenance of transmission device. Lubricating oil shall be added before use. The brand of lubricating oil is lkc100150# medium load extreme pressure industrial gear oil.

2、滾簡軸承的潤滑。滾簡軸承為UCP系列(常用UCP214)，用潤滑脂潤滑，每天加油一次。

2. Lubrication of roller bearings. The plain roller bearing is UCP series (commonly used ucp214), which is lubricated with grease and filled once a day.

3、滾簡與托輥的清理。自上料攪拌車，經常清理滾簡和托輥上的積料，積料過多會影響皮帶的運行，出現跑偏的情況。自上料攪拌車

3. Cleaning of roller and idler. From the feeding mixer truck, the accumulated materials on the roller and idler are often cleaned. Too much accumulated materials will affect the operation of the belt and lead to deviation. Self loading mixer

4、刮砂裝置的維護。定期檢查刮砂裝置的磨損程度，刮砂裝置磨損到一定程度后及時更換。

4. Maintenance of sand scraper. Regularly check the wear degree of the sand scraper, and replace the sand scraper in time after it is worn to a certain extent.

5、自上料攪拌車，橡皮擋邊的更換。橡皮擋邊磨損嚴重，有料撒出時應及時更換。

5. Replacement of rubber retaining edge of self loading mixer. The rubber retaining edge is seriously worn, and it shall be replaced in time when materials are scattered.

6、接口斷裂及橫向撕裂的防范及處理。接頭硫化處理不合格; 沖擊負載過大，薄弱部分受交變應力影響斷裂;接口方向與皮帶運動方向不合適；長期使用等，嚴重?fù)p壞皮帶。自上料攪拌車，在使用時要盡量減少負載，特別是有配重張緊裝置的皮帶，應控制配重在200kg~300kg內，以雨季不打滑為宜，加強巡查，防止異物卡死皮帶，劃傷皮帶;加強對皮帶裝配人員的培訓，防止皮帶接口方向裝反。

6. Prevention and treatment of interface fracture and transverse tear. The joint vulcanization treatment is unqualified; The impact load is too large, and the weak part breaks under the influence of alternating stress; The interface direction is not suitable for the belt movement direction; If it is used for a long time, the belt will be seriously damaged. When using the self loading mixer truck, the load shall be reduced as far as possible, especially the belt with counterweight tensioning device. The counterweight shall be controlled within 200kg ~ 300kg, and it is better not to slip in rainy season. Patrol inspection shall be strengthened to prevent foreign matters from blocking the belt and scratching the belt; Strengthen the training of belt assembly personnel to prevent reverse installation of belt interface.